Numerical Investigation of the Effect of Linear, Parabolic, and Radial Fin Geometries on the Melting Performance of RT35 Phase Change Material in a Triple-Tube Heat Exchanger
Pages 482-503
https://doi.org/10.22034/masm.2026.740745
Tahereh Hassani Jalilian, َAshkan Ghafouri
Abstract The low thermal conductivity of phase change materials (PCMs) remains the main challenge for their widespread application in latent heat thermal energy storage systems. In the present study, the effect of curved-shaped fins on improving the melting rate of RT35 PCM in a triple-tube heat exchanger is numerically and two-dimensionally investigated. Simulations are performed using ANSYS Fluent CFD software employing the enthalpy-porosity method. The effects of two key parameters—the number of linear fins (3, 4, and 5) and fin geometry (linear, parabolic, and radial)—on liquid fraction, temperature distribution, and velocity field during the melting process are studied. The results demonstrate that increasing the number of linear fins from 3 to 5 enhances the liquid fraction by 27% and 41% at 600 seconds, respectively, and improves the PCM temperature by up to 15 K. Comparing different fin shapes reveals that parabolic and radial fins increase the liquid fraction by 13% compared to the linear configuration at 400 seconds. Moreover, the complete melting time in the five-fin parabolic configuration decreases by 50% compared to the five-fin linear case and by 68% compared to the three-fin linear case. Overall, fins with greater curvature exhibit superior thermal performance due to enhanced buoyancy forces and improved natural convection flow. The findings of this research can be utilized in the optimal design of thermal energy storage heat exchangers for applications in air conditioning systems, solar collectors, and industrial waste heat recovery.
Vibration Analysis of Composite Beams with Vertically Laminated Structure Based on Timoshenko Beam Theory
Pages 504-526
https://doi.org/10.66224/masm.2026.2093181.1193
saeed abolghasemi
Abstract This paper introduces a vertically laminated configuration for composite beams and investigates its effect on the vibrational behavior of the beam. For this purpose, the governing equations of the problem are first derived using Timoshenko beam theory. Then, by defining the constitutive relations for two types of laminate configurations, including the conventional horizontal lamination used in composite beams and the proposed vertical lamination, the governing equations are expressed in terms of the beam displacement components, resulting in a system of coupled differential equations. Subsequently, by developing an analytical approach, the governing equations are solved simultaneously without the need for decoupling, and the natural frequencies of the beam are obtained. Natural frequency analysis results for both horizontal and vertical laminate configurations under different boundary conditions and stacking sequences are presented and compared. The results demonstrate that, unlike the horizontal laminate configuration, the natural frequency of the beam in the vertically laminated configuration can be controlled and optimized by changing the fiber angle orientation. This characteristic can be of significant importance in the design of composite structures, enabling the development of beams with desirable dynamic properties for specific applications.
Investigation, sensitivity analysis and optimization of effective parameters of roughness geometry of absorber plates of solar air heaters with repeating V-shaped geometry on Nusselt number
Pages 527-550
https://doi.org/10.66224/masm.2026.2087180.1186
Saeed Tahmasbi, Abdolreza Moghadassi, Hamed Safikhani
Abstract Solar air heaters are widely used to save energy, especially in cases where high temperatures are not required. Among its applications are space heating, water desalination, and drying a range of products, including marine products that are used continuously. Since the thermal efficiency of solar air heaters is low, most research in investigating the types of roughness in terms of shape, size, and orientation concerning the flow direction tries to achieve an optimal arrangement and geometry of the roughness.
This article attempts to make the Nusselt number in a rectangular channel with artificial roughness and a V-shaped arrangement repeatable.
In addition, this air heater and the method of changing the parameters are investigated and optimized to the geometry of the roughness and operating parameters.
In this article, while examining solar air heaters and the roughness geometry of their absorber plates, a systematic analysis using statistical modeling method, Sobel sensitivity analysis, for important process input parameters including Reynolds number, relative groove height, relative groove pitch and angle of incidence in the geometry of artificial roughness of the absorber plate of the solar air heater, has been carried out on the behavior of the Nusselt number output responses.
This article also discusses single-objective optimization to achieve the highest Nusselt number using the Deringer statistical algorithm.
Fabrication of selective heterogeneous cation exchange membrane by using synthesized metal-organic framework for heavy metal ions removal from water
Pages 551-567
https://doi.org/10.61186/masm.2025.2052107.1151
Saba Sohrabnejad, Sayed Mohsen Hosseini, Fahime Parvizian, Mohammad Yaser Masoomi
Abstract In this research, the highly selective heterogeneous cation exchange membrane based on metal-organic frame works (MOFs) was prepared and introduced to electrodialysis system as hopeful material for the removal of heavy metal ions. MIL-101 (Fe) particles were fabricated via a simple chemical technique and suggested into matrix of the ion exchange membranes as additive particles. The membranes were prepared via solution casting technique by applying the desired concentrations of additive particles (0, 0.5, 1, 1.5, 2, 3 (wt%)) and then the effect of the additive particles on the morphology, electrochemical properties, and overall performance in electrodialysis system was studied. the synthesized MOF and homemade membranes were characterized using FTIR, FESEM, EDX and AFM. the images related to morphological studies showed uniform distribution of MIL-101 (Fe) particles in matrix of membranes. Utilizing MIL-101 (Fe) particles in the membrane body led to increase of surface hydrophilicity. The Water content of modified membranes was enhanced considerably compare to pristine. The membrane potential, transport number and permselectivity were increased by applying MIL-101 (Fe) loading ratio up to 1.5 wt% and then decreased. MIL-101 (Fe) membranes also, have considerable performance in removal of lead ions, so that modified sample with 2 wt% of MOF particles displayed a significant increase of 190% compare to pristine. The results are useful for electo-membrane process specially electrodialysis in order to water treatment.
Dynamic Interaction between an AFM Oscillating Cantilever and Human Liver Epithelial Cells: Analysis of Cellular Mechanical Properties
Pages 568-589
https://doi.org/10.66224/masm.2026.2105527.1206
Ali Sadeghi, Shahrokh Shojaei, Mansoureh Lafouti, Farimah Mahin Shafie
Abstract In this study, the nanomechanical properties and dynamic response of healthy and cancerous human liver cells before and after treatments were investigated using atomic force microscopy (AFM). The Young’s modulus of healthy and untreated cancerous cells was measured at 2.940±1.069kPa and 0.785±0.282kPa, respectively. Treatment with cisplatin, atmospheric cold plasma (DBD), and their combined therapy increased the Young’s modulus of cancer cells to 2.218، 2.780 and 3.660±1.811, respectively. Furthermore, the enhanced cellular stiffness induced a shift in the AFM cantilever resonance frequency toward higher values, increasing the first-mode frequency from 3.98 kHz to 4.35 kHz. An analytical model based on Timoshenko beam theory and the DMT contact model showed excellent agreement with experimental and finite element method (FEM) results, with a relative error below 7.205%. These findings demonstrate that coupling nanomechanical characterization with AFM dynamic analysis provides a precise and non-destructive tool for evaluating cancer cell mechanical properties and monitoring therapeutic efficacy.
Using Sliding Mode Nonlinear Control Method to Model Nanomanipulation Process using Atomic Force Microscope
Pages 590-618
https://doi.org/10.61186/masm.2026.2073922.1171
zohreh moradi, Mohsen Shafieirad, Alireza Faraji
Abstract Recent advances in nanotechnology have highlighted the need for precise and stable methods for manipulating both biological and non-biological particles. Among the available tools, atomic force microscopy (AFM) is considered a key instrument due to its high capability for controlled contact and measurement of extremely small displacements. However, maintaining stable contact between the probe tip and the particle and preventing undesired slippage, especially when dealing with complex geometries, remains a significant challenge. In this study, a dynamic modeling framework combined with sliding mode control (SMC) was proposed to enhance AFM performance during particle manipulation. Simulation results demonstrated that the designed controller could maintain the probe’s position and angle with high accuracy. Examination of three particle geometries—spherical, cylindrical, and chamfered cylindrical—revealed that slippage increased with surface complexity, with spherical particles exhibiting the least sliding (3.4%) and chamfered cylindrical particles the most (4.8%). Furthermore, a comparison of three cantilever types showed that the V-shaped cantilever achieved the best performance, with only 2.1% sliding and a significant reduction in angular fluctuations.These findings indicate that combining accurate dynamic modeling with sliding mode control provides an effective approach for developing advanced AFM systems and expanding their applications in biological studies and tissue engineering.
Analysis of mechanical and structural performance of AA5052/AA1200 dissimilar aluminum alloy joints produced by FSW and GTAW processes
Pages 619-637
https://doi.org/10.22034/masm.2026.741608
Hamidreza Rezaei Ashtiani, Davood Bagheri
Abstract Achieving appropriate bond strength between two or more sheets of different alloys is of particular importance. Conventional methods for producing bimetallic sheets include fusion welding processes such as gas tungsten arc welding (GTAW) or (TIG) and friction stir welding (FSW). This study investigates the mechanical properties and microstructure of bimetallic samples made from dissimilar aluminum alloys AA5052 and AA1200 joined by GTAW and FSW. Mechanical tests showed that in FSW samples, rupture occurred in the weld zone, whereas in TIG samples, fracture occurred in the base metal. Microhardness tests indicate higher hardness in the weld zone of GTAW (TIG) samples due to the use of 5356 ER filler compared to FSW. Finally, tensile test analysis and comparison determined that the TIG method outperformed FSW for joining some sheets.Finally, by analyzing and comparing the tensile test results, it was determined that the TIG method performs better than FSW in joining some sheets.
